After getting your supplies and frame materials then it is time to get down and do the actual work of framing. This starts with choosing the space you will be working from. It is recommended that this should be a clean and flat surface like a large table of the counter tops in the kitchen. The work surface should be protected using a Kraft paper, a corrugated board or a table pad. The following are the basics of picture framing Dublin.
The package containing the materials you need in order to do this are opened up and organized. Make sure to check and confirm that all that you ordered is included just as per your order. The materials used in packaging should not be thrown away until the work of framing is done to satisfaction and hung up.
Assemble the tools that you need in your work to avoid distractions. Also gather the important tools such as the screw driver, wire, acrylic cleaner and also the linen tape. Some other accessories and tools can be ordered online in Ireland to make your work easier but they are not all that necessary.
Begin by fixing your art to the back of the foam core then tape or hinge the mat sheet to this mat board or the form core according to your preference. Then set them aside as you perform other procedures.
The next step is preparation of acrylic. This is done by peeling a side of protective liner from the side that will come into contact with the piece of art. The peeled side is placed side down on the assembly of the art and the other side is peeled off. In the case where the acrylic been used has ultra violet or non-glaring properties then the side to face up is usually indicated on package.
If you are working with a metallic frame you should choose side and also the bottom rails to be placed facing down on the surface you are working in. The corner brackets are to be inserted and tightened. The art is slid within the partly assembled frame. Frame treatment is also placed face down then top rail inserted and the corners tightened. Spring clips are put beneath the frame for a nice and also tight fit. Bumpers and hanging ware are attached last.
If the frame you are working with is wooden then it is delivered assembled if its matted length and width is fifty four or less. You proceed from putting it face down and then placing the art face down on inside it too. The art is secured within using clips. The hanging hardware and wires are then screwed. Some framers use point drivers for securing the art into the frame. To get a finished look at the back a double stick tape is run along edges of the frame and a Kraft paper attached. The excess is trimmed off and hanging ware and bumpers attached.
Before hanging it is recommended to always polish the finished work using a squirts of acrylic cleaner made of Novus. The polishing works to ensure that the picture looks great and presentable which is of course the ultimate goal of any art framer.
The package containing the materials you need in order to do this are opened up and organized. Make sure to check and confirm that all that you ordered is included just as per your order. The materials used in packaging should not be thrown away until the work of framing is done to satisfaction and hung up.
Assemble the tools that you need in your work to avoid distractions. Also gather the important tools such as the screw driver, wire, acrylic cleaner and also the linen tape. Some other accessories and tools can be ordered online in Ireland to make your work easier but they are not all that necessary.
Begin by fixing your art to the back of the foam core then tape or hinge the mat sheet to this mat board or the form core according to your preference. Then set them aside as you perform other procedures.
The next step is preparation of acrylic. This is done by peeling a side of protective liner from the side that will come into contact with the piece of art. The peeled side is placed side down on the assembly of the art and the other side is peeled off. In the case where the acrylic been used has ultra violet or non-glaring properties then the side to face up is usually indicated on package.
If you are working with a metallic frame you should choose side and also the bottom rails to be placed facing down on the surface you are working in. The corner brackets are to be inserted and tightened. The art is slid within the partly assembled frame. Frame treatment is also placed face down then top rail inserted and the corners tightened. Spring clips are put beneath the frame for a nice and also tight fit. Bumpers and hanging ware are attached last.
If the frame you are working with is wooden then it is delivered assembled if its matted length and width is fifty four or less. You proceed from putting it face down and then placing the art face down on inside it too. The art is secured within using clips. The hanging hardware and wires are then screwed. Some framers use point drivers for securing the art into the frame. To get a finished look at the back a double stick tape is run along edges of the frame and a Kraft paper attached. The excess is trimmed off and hanging ware and bumpers attached.
Before hanging it is recommended to always polish the finished work using a squirts of acrylic cleaner made of Novus. The polishing works to ensure that the picture looks great and presentable which is of course the ultimate goal of any art framer.
About the Author:
You can find a detailed summary of the reasons why you should use picture framing Dublin services at http://warrensphotography.com right now.
No comments:
Post a Comment